SA516-70 Drum Boiler Tekanan Pabrik Gula Untuk Menyimpan Air Panas
Detail Produk
| Nama Produk: | Drum uap | Aplikasi: | Sistem Boiler dan Sistem Industri |
|---|---|---|---|
| Bahan: | SA516-70 | Sertifikasi: | ISO9001, ASME, EN |
| Menyoroti |
Drum boiler tekanan SA516-70,drum boiler tekanan Pabrik Gula,drum boiler uap SA516-70 |
||
Deskripsi Produk
Bagian Boiler Steam Drum Terbuat dari SA516-70 untuk Pabrik Gula dalam Standar ASME
Definisi
Drum uap boiler adalah bejana tekan terpenting dalam boiler industri untuk menyimpan air panas dan uap.Dalam sistem pipa boiler industri, tidak semua air panas dapat sepenuhnya diuapkan menjadi uap, melainkan campuran uap dan air panas.Karena air panas jenuh membutuhkan lebih banyak panas untuk diubah menjadi uap, drum uap boiler adalah peralatan yang diperlukan.Steam drum memisahkan air panas dan uap, dimana campuran masih mengalir kembali untuk dipanaskan kembali melalui down comer.
Klasifikasi
| Tekanan | Rendah | Tengah | Tinggi | Sangat tinggi |
| Diameter dalam (mm) |
∅ 800-1200 |
∅ 1400-1600 |
∅ 1600-1800 |
∅ 1600-1800 |
| Ketebalan (mm) | 16-25 | 32-46 | 60-100 | 80-100 |
| Bahan | Baja karbon | Baja karbon & baja paduan | Baja karbon & baja paduan | Baja paduan |
Aksesoris
Komponen utama dalam sistem boiler adalah boiler feedwater heater, deaerator, boiler, feed pump, economizer, boiler, superheater, attemperator, sistem steam, kondensor dan pompa kondensat.Selain itu ada set kontrol untuk memantau aliran air dan uap, aliran bahan bakar, aliran udara dan penambahan perlakuan kimia.
Kontrol kualitas
1. Laporan uji dampak dan perhitungan Kekuatan dengan informasi bahan yang diterapkan.
2. 100% NDT (inspeksi non-destruktif) laporan pelat baja, tabung dan elektroda
3. Laporan inspeksi uji penetran sinar-X, -ray dan cair (jahitan las): untuk memastikan kualitas seluruh boiler
4. Laporan uji hidraulik: pastikan tekanan dan keamanan kerja standar
Sorotan Produk
Bagian Boiler Steam Drum Terbuat dari SA516-70 untuk Pabrik Gula dalam Standar ASME Definisi Drum uap boiler adalah bejana tekan terpenting dalam boiler industri untuk menyimpan air panas dan uap.Dalam sistem pipa boiler industri, tidak semua air panas dapat sepenuhnya diuapkan menjadi uap, ...
Pemanasan dinding membran permukaan Argon arc Pengelasan Untuk Biomass Boiler
High Pressure Power Boiler Heating Surface Membrane Wall Argon Arc Welding For Biomass Boiler Product Introduction Water wall panels with pins usually laid vertically on the inner wall of the furnace wall, it is mainly used to absorb the radiant heat emitted by the flame and high-temperature flue gas in the furnace.It is the main type of evaporating heating surface of all kinds of modern boilers and the basic component of boiler water circulation loop.Because of both cooling
High Frequency Welding H Fin Tube Economizer Untuk Boiler PLTN ASME
High Frequency Welding H Fin Tube Economizer For Power Plant Boiler ASME Product Description The boiler economizer is a device used to recover waste heat in industrial boilers, usually located at the tail of the flue of the boiler, which increases the feed water temperature and reduces fuel consumption by absorbing the heat of the flue gas, so as to achieve the effect of energy saving and emission reduction. But at the same time, as an environmental protection equipment, the
Baja Karbon SA192 Superheater Coil Argon Arc Welding 100% PT
Product Description: A boiler superheater is an essential component in a boiler system, responsible for increasing the temperature of steam produced by the boiler. One of the key products in this category is the Superheater Coil, designed to enhance the efficiency and performance of boiler systems. This particular superheater is suitable for various fuels, including coal, oil, and biomass, making it versatile and adaptable to different energy sources. The Superheater Coil
Boiler Industrial SA210A1 Boiler baja Economizer Bagian Pertukaran Panas Sertifikasi ASME
Boiler Industrial SA210A1 Steel Boiler Economizer Heat Exchange Part ASME Certification Introduction The H-shaped finned tube is also known as the H-shaped fin tube, also known as the butterfly fin tube. It is to weld symmetrically two pieces of steel with an arc in the middle to form fins (ribs or butterflies), the frontal shape of which resembles the letter "H", so it is called the H-shaped finned tube. The two fins of the H-shaped fin tube are rectangular and approximately
Silakan gunakan formulir kontak pertanyaan online kami di bawah ini jika Anda memiliki pertanyaan, tim kami akan menghubungi Anda sesegera mungkin.
