Generator Sistem Pemulihan Panas Tahan Lama Beredar Secara Alami Tekanan Tinggi
Detail Produk
| Tipe: | Sirkulasi Alami | Tekanan: | Tekanan tinggi |
|---|---|---|---|
| Kondisi: | Baru | Bobot: | Disesuaikan |
| Pengobatan permukaan: | Dilukis | Harga: | Dapat dinegosiasikan |
| Menyoroti |
boiler pemulihan panas limbah,boiler industri dan generator uap pemulihan panas |
||
Deskripsi Produk
HRSG Heat Recovery Steam Generator Tekanan Tinggi Beredar Secara Alami untuk Industri
Produksi HRSG
Perpindahan panas sangat baik, karena penggunaan pemanas awal udara pipa panas canggih.Selain ukurannya yang ringkas, membuat tapak yang lebih kecil.Di depan, ada kotak asap yang tahan ledakan, memberikan peningkatan keamanan dan stabilitas operasi boiler.
| Mode | Dimensi (m) |
| Q6.41000-2-1.25 | |
| Q33 / 550-6-1.25 | 8.08x2.853.7 |
| QC55 / 530-8-1.0 | 7x3x5.5 |
| P50 / 700-14-1.25 / 350 | 16x37.5 |
| FGP320-1.25 / 320 | 8,8x6,77x9,7 |
| P50 / 954-20-1.6 | 9,77x7.52x6.73 |
| Q121.5 / 860-37.8-4.25 / 343 | |
| QC16 / 850-5-1.6 / 250 | 7x3.5x4.5 |
| QC36 / 650-8-1.25 | 10xB.5x31 |
| Kapasitas lini produksi semen t / d | 1000 | 2500 | 5.000 | 10000 | |
| Aliran masuk boiler Nm3/ h | Kiln (depan) | 60.000 | 88000 | 243000 | 472000 |
| Kiln (ekor) | 76000 | 170000 | 328000 | 612000 | |
| Suhu gas masuk boiler ℃ | Kiln (depan) | 370 | 360 | 380 | 390 |
| Kiln (ekor) | 360 | 320 ~ 360 | 330 | 330 | |
| Nilai penguapan t / jam | Kiln (depan) | 5.8 | 7.25 | 24 | 50 |
| Kiln (ekor) | 7.5 | 10 ~ 15.8 | 20 ~ 24.6 | 35.5 | |
| Nilai tekanan uap Mpa | Kiln (depan) | 1.25 | 1.25 | 1.25 | 1.25 |
| Kiln (ekor) | 1.25 | 1.25 | 1.25 | 1.25 | |
| Suhu uap terukur ℃ | Kiln (depan) | 340 | 330 | 350 | 360 |
| Kiln (ekor) | 340 | 300 ~ 340 | 310 | 310 | |
| Struktur boiler | Kiln (depan) | Vertikal | Vertikal | Vertikal | Vertikal |
| Kiln (ekor) | Vertikal | Vertikal dan Horizontal | Vertikal dan Horizontal | Vertic | |
Sorotan Produk
HRSG Heat Recovery Steam Generator Tekanan Tinggi Beredar Secara Alami untuk Industri Produksi HRSG Biaya penempatan dan investasi sangat berkurang karena bentuk perakitan yang ringkas, dari boiler.Tabung air samping kiri dan kanan boiler menggunakan konstruksi dinding membran, yang dapat bekerja ...
Pemanasan dinding membran permukaan Argon arc Pengelasan Untuk Biomass Boiler
High Pressure Power Boiler Heating Surface Membrane Wall Argon Arc Welding For Biomass Boiler Product Introduction Water wall panels with pins usually laid vertically on the inner wall of the furnace wall, it is mainly used to absorb the radiant heat emitted by the flame and high-temperature flue gas in the furnace.It is the main type of evaporating heating surface of all kinds of modern boilers and the basic component of boiler water circulation loop.Because of both cooling
High Frequency Welding H Fin Tube Economizer Untuk Boiler PLTN ASME
High Frequency Welding H Fin Tube Economizer For Power Plant Boiler ASME Product Description The boiler economizer is a device used to recover waste heat in industrial boilers, usually located at the tail of the flue of the boiler, which increases the feed water temperature and reduces fuel consumption by absorbing the heat of the flue gas, so as to achieve the effect of energy saving and emission reduction. But at the same time, as an environmental protection equipment, the
Baja Karbon SA192 Superheater Coil Argon Arc Welding 100% PT
Product Description: A boiler superheater is an essential component in a boiler system, responsible for increasing the temperature of steam produced by the boiler. One of the key products in this category is the Superheater Coil, designed to enhance the efficiency and performance of boiler systems. This particular superheater is suitable for various fuels, including coal, oil, and biomass, making it versatile and adaptable to different energy sources. The Superheater Coil
Boiler Industrial SA210A1 Boiler baja Economizer Bagian Pertukaran Panas Sertifikasi ASME
Boiler Industrial SA210A1 Steel Boiler Economizer Heat Exchange Part ASME Certification Introduction The H-shaped finned tube is also known as the H-shaped fin tube, also known as the butterfly fin tube. It is to weld symmetrically two pieces of steel with an arc in the middle to form fins (ribs or butterflies), the frontal shape of which resembles the letter "H", so it is called the H-shaped finned tube. The two fins of the H-shaped fin tube are rectangular and approximately
Silakan gunakan formulir kontak pertanyaan online kami di bawah ini jika Anda memiliki pertanyaan, tim kami akan menghubungi Anda sesegera mungkin.
