Kepala Boiler Baja Karbon dengan Max. 20t/h Produksi Uap dan Desain Tabung Air Sirkulasi Alami
Detail Produk
| Jenis: | Sirkulasi Alam | Struktur: | Tabung Air |
|---|---|---|---|
| Tekanan: | Tekanan tinggi | Produksi Uap: | <i>Max.</i> <b>Maks.</b> <i>20t/h</i> <b>20t/jam</b> |
| Gaya: | Horisontal | Keluaran: | Air panas |
| Desain bahan bakar: | Bahan bakar batubara | Bahan: | Plat baja boiler khusus |
| Bahan bakar yang berlaku: | Butiran pembentuk biomassa | Bahan bakar: | Batubara |
| Berat: | 1-20ton | Diameter: | 76mm~914mm |
| Panjang: | 23000mm | Suhu: | 300~1500℃ |
| Komponen inti: | Noenname_null | ||
| Menyoroti |
Max. 20t/h Kepala Boiler,Header uap sirkulasi alami,Panci tabung air Headers manifold |
||
Deskripsi Produk
Headers mengumpulkan dan mendistribusikan uap atau air dari atau ke serangkaian pipa atau saluran yang lebih kecil.Berbeda dengan sistem pipa yang biasanya dibenturkan dan ditekuk, header mempertahankan konfigurasi lurus.
Tekanan dan suhu operasi tergantung pada komponen yang terhubung.Header yang terhubung ke penghemat atau panel dinding air menghadapi persyaratan material yang kurang ketat daripada yang terhubung ke superheater atau reheater.
Tersedia dalam baja karbon hingga baja ferit tinggi (termasuk T/P91 dan T/P92), dengan diameter mulai dari 88,9 mm hingga 406,4 mm.
Bagian kepala tekanan boiler uap dengan pipa las longitudinal diameter besar meliputi:
- Headers dinding air
- Headers superheater
- Header penghemat
Komponen-komponen ini berfungsi untuk mengumpulkan, mencampur, dan mendistribusikan kembali media kerja.
| Parameter | Nilai |
|---|---|
| Diameter (OD) | Ø76mm~Ø914mm |
| Panjang (Max) | 23000mm |
| Suhu | 300 ~ 1500°C |
Alamat:No.1 Dongli Road, Donglai, Kota Zhangjiagang, Provinsi Jiangsu, Cina
Tel:+86 (0) 512 5866 6196
Fax:+86(0) 512 5877 4453
Situs web:Pengolahan bahan bakar
Sorotan Produk
Header boiler baja karbon bertekanan tinggi untuk pembangkit listrik industri, sesuai dengan standar Amerika. Dilengkapi dengan sirkulasi alami, struktur tabung air, dan produksi uap maks. 20t/jam. Ukuran khusus (OD 76-914mm), garansi 1 tahun, cakupan komponen inti 5 tahun. Bersertifikasi untuk keselamatan dengan dukungan insinyur luar negeri.
Pemanasan dinding membran permukaan Argon arc Pengelasan Untuk Biomass Boiler
High Pressure Power Boiler Heating Surface Membrane Wall Argon Arc Welding For Biomass Boiler Product Introduction Water wall panels with pins usually laid vertically on the inner wall of the furnace wall, it is mainly used to absorb the radiant heat emitted by the flame and high-temperature flue gas in the furnace.It is the main type of evaporating heating surface of all kinds of modern boilers and the basic component of boiler water circulation loop.Because of both cooling
High Frequency Welding H Fin Tube Economizer Untuk Boiler PLTN ASME
High Frequency Welding H Fin Tube Economizer For Power Plant Boiler ASME Product Description The boiler economizer is a device used to recover waste heat in industrial boilers, usually located at the tail of the flue of the boiler, which increases the feed water temperature and reduces fuel consumption by absorbing the heat of the flue gas, so as to achieve the effect of energy saving and emission reduction. But at the same time, as an environmental protection equipment, the
Baja Karbon SA192 Superheater Coil Argon Arc Welding 100% PT
Product Description: A boiler superheater is an essential component in a boiler system, responsible for increasing the temperature of steam produced by the boiler. One of the key products in this category is the Superheater Coil, designed to enhance the efficiency and performance of boiler systems. This particular superheater is suitable for various fuels, including coal, oil, and biomass, making it versatile and adaptable to different energy sources. The Superheater Coil
Boiler Industrial SA210A1 Boiler baja Economizer Bagian Pertukaran Panas Sertifikasi ASME
Boiler Industrial SA210A1 Steel Boiler Economizer Heat Exchange Part ASME Certification Introduction The H-shaped finned tube is also known as the H-shaped fin tube, also known as the butterfly fin tube. It is to weld symmetrically two pieces of steel with an arc in the middle to form fins (ribs or butterflies), the frontal shape of which resembles the letter "H", so it is called the H-shaped finned tube. The two fins of the H-shaped fin tube are rectangular and approximately
Silakan gunakan formulir kontak pertanyaan online kami di bawah ini jika Anda memiliki pertanyaan, tim kami akan menghubungi Anda sesegera mungkin.
